For Your Motorcycle

Smart in-line 3300mA USB charger kit, with standby mode and vehicle battery monitor.

The sealed in-line battery to USB 3300mA charger with 200cm / 80″ of cable and O-31 battery lead, delivers safe and fast USB charging of any device mounted outside on the handlebar or inside your tank or pannier – Cable routes to where USB charging is needed!

Supply cable (100cm / 40″) with M6 / 1/4″ rings fit all powersport battery terminals. – Fuse protected.

Charges 1x USB device with up to 3300mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Weatherproof USB charge port easily zip-tie to handlebar, strut or even brake / clutch cable – Seals againt inserted USB cable for charging in any weather!

Built in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – Indicates battery is ‘start ready’ at the blink of an LED!

Smart 2400mA USB charger, with standby mode & vehicle battery monitor.

The portable & compact SAE to USB 2400mA charger for safe and fast charging of any USB device, including your phone, camera or GPS.

Connects to battery lead with industry standard SAE 2-pin connector – Seals perfectly when mated with OptiMate SAE!

Charges 1x USB device with up to 2400mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Creates weatherproof seal against inserted USB cable, or ‘rideproof’ cap seals when not in use – Worry free phone, camera or GPS charging in any weather!

Built-in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – indicates battery is ‘start ready’ at the blink of an LED!

NOTE: Due to manufacturer restrictions, this item cannot be shipped to addresses outside of Canada.

The maintenance of textile garments requires special attention, especially when they contain waterproof and breathable membranes. REVIT! TEXTILE WASH detergent maintains the specific qualities of breathable waterproof clothing, when washing by machine or hand.

Always follow the wash and care instructions on garment labels.

FEATURES

• Long Life 100% synthetic fluid
• Applications: All types of hydraulic actuated-brake and clutch systems in accordance with DOT 5.1, DOT 4 and DOT 3 manufacturers' recommendations.
• Fluidity specially designed for anti-locking brake system (ABS)

SPECIFICATIONS

• Dry Boiling Point: 270°C (518°F)
• Wet Boiling Point: 185°C (365°F)
• Standards: FMVSS 116 DOT 5.1 non silicone base & DOT 4 & DOT 3 / SAE J 1703

IPONE VISOR RAIN OFF is a visor cleaner with a water-repellent effect. It places a protective film on the visor allowing water to slide off easily.

Spray the product on the visor, let it dry for 2 minutes and wipe with a soft cloth.

• Repels water from helmet visor
• Improves visibility by shedding water
• Suitable for glossy and matte helmets
• No marks

Colorless and sticky lubricant specifically designed to lubricate all chains of road bikes and karts.

Types of Use

All types of chains: standard and with O-RING, X-RING, Z-RING. Street motorcycles, go-karts. Specially recommended for very fast motorcycles, MOTUL CHAIN LUBE ROAD adheres to the chain even at high speeds.

Package size: 400ML (9.3OZ)

Colorless and sticky lubricant specifically designed to lubricate all Off-road chains.

Types of Use

All types of chains : standard and with O-RING, X-RING, Z-RING.
Cross, enduro, trial, trail motorcycles or quads, ATVs.
Specially recommended for off road use: MOTUL CHAIN LUBE OFF ROAD repels sand and soil.

Package size: 400ML (9.3OZ)

• Double-ended brush for cleaning chains and other components
• Three-sided brush to clean chain rollers and side plates in one operation
• Long, straight bristles on opposite end to clean hard to reach areas
• Durable nylon brush and high quality plastic handle

100% Synthetic Ester based motorcycle lubricant for high performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial fitted with 4-stroke engines, integrated or non-integrated gearbox, wet or dry clutch, engines meeting Euro 2 or Euro 3 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe. 

Types of Use

High performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems : catalytic converters, air injection into exhaust pipe...

Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

Technosynthese® 4-Stroke lubricant – Ester technology - Improved shear resistance. Smooth shifting. Meets JASO MA2 specifications for optimal wet clutch performance. Suitable for catalytic converters.

Types of Use

Street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 Stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe... Suitable for specific SUZUKI, YAMAHA, KAWASAKI engines requiring SAE 10W-40 viscosity grade oil. Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

Protection

Synthetic lubricant Technosynthese® reinforced by Ester base stock to warranty anti-wear properties and improve gear protection and lifetime. Improved oil film resistance at high temperatures for engine durability. Optimized Phosphorus and Sulfur content (JASO MA2 < 1200 ppm) for better operating conditions of catalytic converters. The innovative anti wear additives package provides excellent gearbox protection. FZG Gear Test results: Pass FLS 14. The FZG (Forschungsstelle für Zahnrader und Getriebebau) Test, evaluates fluid lubricating and wear protection properties at the interface of a loaded set of gears.

Comfort

JASO has created its own 4-stroke motorcycle standard -JASO T903- which has three grades MA, MA1 and MA2. JASO MA2 offers the most efficient friction levels to guarantee the clutch engagement during the three riding modes: Starting, Acceleration and Constant Speed.

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF204RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models, including most Triumphs. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/hf204rc

If you’re changing your oil filter, make sure to also pick up a new oil drain plug washer here.

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF153RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/HF153RC

HD 80W-90 is an Extreme Pressure gearbox and differental lubricant.

Motul HD 80W90 Transmission Oil

Motul's most robust gearbox oil is the HD 80W90 Transmission Oil. Prepared for abuse, Motul HD Transmission Oil is suitable for all mechanical transmissions: synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes and hypoid differentials without limited slip systems. Motul HD is anti-foam, anti-corrosion and stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard.

Features: 

• Fully conventional formulation
• Designed especially for high load applications
• Extreme anti-wear properties
• Stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard
• Suitable for all transmissions without limited slip systems
• Safe for synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes or hypoid differentials
• Recommended for heavy loads and low revolution speed or moderate loads and high revolution speed
• See spec sheet for full details
• Meets or exceeds API GL-4, API GL-5

Counteract CBB-EP8 Tire/Tube Mounting Compound 8lb Bucket

• Designed to assist in mounting rubber tires and tubes on all types and sizes of wheels
• Fortified with rust inhibitors to provide protection against corrosion of aluminum or alloy wheels
• Fully compatible with Counteract balancing beads
• Fast-drying formula will not freeze
• Performs well on low profile tires or tires with stiff beads
• Environmentally friendly and petroleum-free
• Reduces wear and tear on tire changing equipment
• Available in 8lb bucket

• Easily apply your tire mounting lubricant with control.
• Perfect for euro paste mounting formulas.
• Works best with Counteract Euro Paste tire and tube mounting compound.
• Premium quality brush with soft and flexible head.
• Angled head allows for easier application.

• Flexible shaft allows easy access to awkward locations during removal and installation of hose clamps
• Comfortable grip, high-torque handle
• Hollow drive handle stores sockets and bits
• Contains: 4, 6, & 8mm sockets, 4mm flat head bit and Phillips #2 bit
• Length: 300mm

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• Size: 51-120mm (2" - 4 3/4") dia.
• Overall length: 285 mm (11-1/4")

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• 32 - 76 mm: Overall length: 215 mm (8-7/16")

Fuel Friend Canister, 2Ltr Black

These great little cans made by Hünersdorff in Germany are exactly what you need for a small, yet solid and safe fuel reserve. Specifically made for storage and transport of hazardous substances, perfect for motorcycle trips, all small engines and many other purposes.

Details:

• The smallest can suitable for fuel nozzles on the market
• Emergency reserve for motorcycles, scooters, quads and other small engines
• Small, extremely robust, meets the highest safety requirements
• Suitable for all fuels and petrol products.
• Made in Germany
• Extremely stable
• Filling opening suitable for fuel nozzles
• Patented design
• Weight: 0.44 kg
• Dimensions: Width x Depth x Height - 14 × 9 × 25 cm
• Does fit in the Kriega OS-Bottle Holder, sold separately

The following accessories can be purchased separately if desired:

• Flexible spout
• Lockable rigid spout

SKU: FFB20black

GTIN: 4007228815719

Spout with bellows, black, HD-PE, for fuel cans

• suitable for all current tank openings (petrol and diesel) and all vehicles with petrol misfuelling inhibitors (not suitable for vehicles with diesel misfuelling inhibitors)
• Accessories for FuelFriend 1L, 1.5L and 2L Canisters - sold separately
• With bellows
• Enables easy emptying of jerrycans
• Nozzle external diameter = approx. 20mm
• Length = 265 mm
• outside thread diameter = 38 mm / inside diameter of filling opening = 29 mm
• Made by Hunersdorff in Germany

SKU: 819702

GTIN:

4007228819724

Rigid petrol spout with closure, black, HD-PE for fuel canisters

• rigid spout with screw cap closure and carrying loop for fixing on the can
• with union nut for exact positioning with small tank openings
• captive screw cap
• for combined jerrycan ECO + PROFI
• suitable for FuelFriend 1L, 1.5L, and 2L canisters - sold separately 
• Length = 130 mm
• Nozzle external diameter = 21 mm
• for a = outside thread diameter = 38 mm / (for w = inside diameter of filling opening = 29 mm)

SKU: 

819901

GTIN: 

4007228819908

Spout red, HD-PE

• for FuelFriend 0.5 L canisters - sold separately 
• with rubber rings 6/32 black
• outside thread diameter = 24 mm / inside diameter of filling opening = 18 mm
• Made by Hunersdorff in Germany

SKU: ET-281302

GTIN:

4007228281293

MOTUL Fuel System Clean 300ml
MOTUL FUEL SYSTEM CLEAN is designed to be used in all types of gasoline engine with injection or carburettors, naturally aspirated or turbocharged with or without catalytic converter, using all kind of gasoline. MOTUL FUEL SYSTEM CLEAN effectively cleans dirtying and clogging which appear in the whole fuel system: 
- condensation in the fuel system 
- gumming in the carburettor 
- injector nozzle fouling 
- dirtying of combustion chambers and inlet valves 

MOTUL FUEL SYSTEM CLEAN provides a perfect lubrication during cleaning process and prevents removed micro-particles from depositing. 

A clean fuel system is a necessary condition for an effective engine running. MOTUL FUEL SYSTEM CLEAN allows to: 
- clean the carburettors or the injectors (for a better atomisation) 
- prevent the formation of deposits and varnishes on inlet valves and in combustion chambers 
- disperse condensation water in order to avoid any fuel system oxidation 

A regular use will provide: 
- optimum engine performances 
- fuel savings 
- increased lifetime of fuel system and catalytic converter 
- a reduction of exhaust pollutants emissions 

Directly pour one can of FUEL SYSTEM CLEAN in the tank before refuelling, regularly, depending on the use (shorten intervals in urban use). The fuel system will be then completely cleaned, from the tank to the combustion chamber. A can of FUEL SYTEM CLEAN is sufficient for tank capacity up to 60 litres. 
In case of bigger tank capacity, the recommended mixing ratio is 0.50% (200:1). Do not exceed the recommended proportion. If necessary, proceed to 2 successive treatments. 
Curative treatment : use the product pure by plugging on the fuel system with the adaptation kit

• Concentrated octane booster increases pump gas octane rating
• Eliminates pre-detonation
• Mix either with straight gas or with alcohol and nitrous mixtures
• For 2- or 4-stroke engines
• Legal for all racing applications
• Won't harm or discolor plastic gas tanks
• Cleans fuel delivery systems
• Each ounce (EU: 29.57 ml) of octane booster per gallon (EU: 3.79 L) of gas raises octane rating by four points
• Made in the U.S.A.

• Built in protection turns off USB charging and prevents your parked vehicle's LFP (LiFePO4) or AGM (Pb) battery from draining - starts back up when vehicle engine fires up
• Creates weatherproof seal against inserted USB cable, or 'rideproof' cap protects USB port not in use - worry free phone, camera or GPS charging in any weather
• Charges 2x USB devices with up to 3300mA current available to share - charge current adapts to each connected device for safe recharging
• The portable 3300mA dual USB charger, with 90° elbow BIKE plug connector that fits your BMW and Triumph motorcycle
• Connects to 12 mm DIN/BIKE 12V socket found on BMW and Triumph motorcycles

Helmet, Visor & Goggle Cleaner quickly and safely removes dirt, dust, grime, snow, sweat and oily residue from all helmets, eye wear and goggles. Its been formulated using de-ionised water as recommended by many helmet manufacturers and it’s safe to use on all lens materials including polycarbonate! Helmet, Visor & Goggle cleaner also uses pH-neutral soaps. And you don’t have to worry about the formula either! It’s fully biodegradable and contains no solvents or harmful chemicals.

It's perfect for cleaning motorcycle goggles, cycling glasses and goggles as well as snowboard and ski goggles.

FEATURES

• Formulated using de-ionised water
• pH neutral formula as recommended by helmet manufacturers
• Free from solvents and harmful chemicals
• 100% biodegradable
• Ideal for motorcycle goggles 
• Ideal for cycling glasses and goggles 
• Ideal for snowboard and ski goggles

HOW TO

• Step 1 - Spray Visor, Lens & Goggle Cleaner onto the surface.
• Step 2 - Allow formula to soften any hard contaminant particles.
• Step 3 - Gently wipe with a clean microfibre cloth.

Looking for an all round wonder spray? Look no further! Muc-Off MO-94 covers all the bases with it's incredible formula that quickly and effectively penetrates moisture, lubricates moving parts and leaves a long lasting protective film. MO-94 prevents dirt adhesion and also drives out excess water to keep rust and corrosion at bay. MO-94 isn’t just for bikes, motorcycles or cars. Nope. It works on just about anything. Whether you’ve got a squeaky door hinge, a rusty lock or a bolt that you just can’t turn, MO-94 is all you need.

*Just remember not to apply MO-94 to your bike’s tyre treads and braking surfaces!

FEATURES

• Free seized parts
• Disperses moisture to prevent rust and corrosion
• Provides light lubrication for moving parts
• Reduces metal to metal contact
• Prevents dirt adhesion
• Cuts down on friction to improve component efficiency
• Weight - 400g
• Biodegradable*

*Contents only.

HOW TO

1. Apply Disc Brake Covers to prevent over-spray and contaminating your discs and pads
2. Spray MO-94 over the desired area for treatment
3. You can use the pink directional straw for smaller, harder to reach parts
4. Allow area to dry
5. Wipe away any excess using a microfibre cloth

Muc-Off Foam Fresh is a highly effective, easy to use foam cleaner which is ideal for helmet liners or any soft material which comes into contact with the rider. Foam Fresh has an instant foaming action, which gently agitates dirt and grime away from the surface leaving a fresh Citric Burst fragrance. Even the cleanest looking riding gear benefits from this uniquely formulated product. It's awesome for use on pads, gloves, shoes, liners and body armour.

FEATURES

• Highly effective, easy to use foam cleaner which is ideal for helmet liners or any soft material which comes into contact with the rider
• Foam Fresh has an instant foaming action, which gently agitates dirt and grime away from the surface leaving a fresh Citric Burst fragrance
• Even the cleanest looking riding gear benefits from this uniquely formulated product
• Also for use on pads, gloves, shoes, liners and body armor
• Available in 400mL aerosol cans

Got a load of grime, mud or oil build up on your machine’s chain and sprockets? Then reach for our Powersports Drivetrain Cleaner! This product will make light work of the toughest of residue from all drivetrain areas, thanks to its fast and effective biodegradable formula. So there’s no need to worry next time you’re out riding on a muddy or wet day, as we’ve got you covered.

FEATURES

• Biodegradable*
• Can be used on all motorcycles, quads, ATVs and UTVs
• Suitable for standard O, X, Z ring chains
• Water-soluble formula
• Fast and effective grease cutting formula
• Removes all chain oil and wax residue from drivetrain and swingarm
• Safely eliminates drive chain contaminants
• Ideal for use with chain cleaning brushes and chain cleaning devices
• Trigger spray included for easy application
• Deep cleans all drive chain areas in seconds
• Safe on metal components, hard plastic, rubber and seals

*Only contents are readily biodegradable.

PLEASE NOTE: Not recommended for non-factory finishes. For best results always test an inconspicuous area before use. Use with caution on painted surfaces. Do not leave on carbon fibre for longer than instructed. Always ensure parts are fully cooled before using. Store in a cool dry place.

DANGER:  Keep  out  of  reach  of  children.  May  be  fatal  if  swallowed  and  enters  airways.  Causes  skin  irritation.  Causes serious eye irritation. Wear protective gloves/eye protection.  IF  SWALLOWED:  Immediately  call  a  POISON  CENTER/doctor.  IF  IN  EYES:  Rinse  cautiously  with  water  for  several  minutes.  Remove  contact  lenses,  if  present  and easy to do. Continue rinsing. Do NOT induce vomiting. IF ON SKIN: Wash with plenty of water/soap. If eye irritation persists: Get medical advice/attention.

Featuring all five Muc-Off brushes in a handy storage bag:

Our Soft Washing Brush with sintered bristle compound is designed to clean your frame and components while caring for delicate finishes. It’s all new design features a tough, impact resistant handle that won't slip in extreme conditions, an oversized head for fast cleaning of large areas and rubberised impact zones for maximum protection.

Our Detailing Brush is ideal for reaching hard-to-shift dirt on sprockets, hubs and other tight areas such as suspension mounts or fork crowns. It’s new design features a tough, impact resistant handle that won't slip in extreme conditions, durable nylon bristles and rubberized impact zones for maximum protection on delicate finishes.

Our Claw Brush features high quality construction with triple brush heads with tough nylon bristles and an integral scraper for mud de-clogging. It’s ideal for chain, cassette and sprockets, and it’s even 10-speed compatible.

Our Wheel & Component Brush is shaped and contoured specifically to clean rims and spokes with ease. Its unique design features an impact-resistant, dual density handle and durable nylon bristles.

Our Two Prong Brush is ideal for reaching hard-to-shift dirt on spokes, discs, shocks, cranks, linkages and pedals. It’s design features a tough, impact resistant handle that won't slip in extreme conditions and durable nylon bristles. The twin brush heads can be altered and repositioned to reach the tightest of areas.

NB: To maintain performance of all brushes avoid use with boiling water and on hot parts. We recommend using warm water and allowing all hot parts to cool before use.

FEATURES

• Sintered bristle compounds for safe cleaning
• Rubberised impact zones for maximum protection
• Nylon bristles for durability
• Contains Two Prong, Detailing, Soft Washing, Claw and Wheel & Component brushes

WHAT'S INCLUDED?

• Soft Washing Brush
• Detailing Brush
• Claw Brush
• Wheel & Component Brush
• Two Prong Brush

Foam Fresh, Visor Cleaner, Premium Anti-Fog Treatment, Microfibre Cloth and Microfibre Detailing Cloth - all the essentials a rider needs to keep their helmet in top condition throughout the season.

Foam Fresh gently agitates dirt and grime away from the inside of your helmet, whilst our Visor Cleaner makes quick work of dirt, dust, grime, snow, sweat or just about any residue left on your goggles, helmet, or eyewear.

All of this is made effortless with our Premium Microfibre Polishing Cloth, utilising the amazing split-fibre technology that vastly increases surface area absorbency.

Finally, our Anti-Fog Treatment means you won’t be left in a haze helping to give you clear vision even under the toughest riding conditions.

FEATURES

Foam Fresh

• Ideal for helmet liners and soft material
• Instant foaming action
• Agitates dirt and grime away from the surface
• Citric Burst fragrance
• For use on pads, gloves, shoes, liners and body armour

Helmet, Visor & Goggle Cleaner

• Formulated using de-ionised water
• pH neutral formula as recommended by helmet manufacturers
• Free from solvents and harmful chemicals
• 100% biodegradable
• Ideal for motorcycle goggles 
• Ideal for cycling glasses and goggles 
• Ideal for snowboard and ski goggles

Microfibre Cloth

• Designed for delicate finishes
• Premium quality microfibre
• Ideal size for carrying around
• Machine washable

Anti-Fog Treatment

• Intensive anti-mist formula
• Advanced moisture absorption
• Lasts up to 5 days
• Safe on all plastics and glass
• Ideal for mx and ski goggles, Snowboard goggles, helmet visors, glasses & car mirrors

WHAT'S INCLUDED?

Silicon Shine not only leaves your bike looking factory fresh, but it also acts as an amazing friction reducer for suspension parts and reduces dirt adhesion. Spray it onto your fork stanchions and rear shocks to reduce resistance for a silky smooth, World Cup performance.

FEATURES

• Protects and leaves a sparkling shine on metal, plastic & rubber parts.
• Reduces friction on fork stanchions and rear shocks
• Silicon formula prevents grime build up on treated surfaces
• Cuts down on future cleaning and maintenance

Don’t let your bottom end get wet with the new Muc-Off Exhaust Bung! Made from a two-part flexible silicone rubber core and sleeve, it creates an awesome leak-proof seal to prevent water or other contaminants from getting into your exhaust pipe whilst you’re cleaning or maintaining your machine. It’s both 2 and 4-stroke compatible thanks to its removable two-part design.

It’s super easy to twist into place and comes with a handy lanyard to make removal easy!

FEATURES

• 2 and 4-stroke compatible thanks to removable 4 stroke bung sleeve
• Tapered design fits most exhaust diameters
• Silicone rubber core construction is sturdy and durable
• Supplied with lanyard for easy removal and storage
• Prevents water or contaminates entering the exhaust during cleaning
• Protects your engine 

HOW TO

Fingerprints and glossy marks are now a thing of the past. Matt Finish Detailer has been specifically developed for satin matt paints, matt finishes and matt vinyl wraps. The premium-grade formula will leave any matt surface with a streak and gloss-free protective finish that reduces dirt adhesion.

FEATURES

• Quick to use spray developed specifically for matt finishes
• Leaves a non-sticky, streak and gloss-free protective finish
• Available in 250ml
• Carbon Fibre safe
• *Biodegradable

*Only contents are biodegradable.

HOW TO

• Step 1 - Shake bottle vigorously.
• Step 2 - Ensure surface is clean, cool and dry. Now apply Matt Finish Detailer to all matt finishes.
• Step 3 - Wipe with a microfibre cloth and leave to dry.
• Note: Mask braking surfaces before application.

Muc-Off Waterless Wash is a highly advanced, easy-to-use spray that cleans and polishes in seconds without the need for water. It details your whole bike, motorcycle, or car in seconds leaving behind a streak free shine. Its innovative formula is designed to encapsulate any surface dirt to prevent scratching and it's safe to use on Carbon Fibre too.

Use it to remove light contaminants in between major washes.

FEATURES

• Cleans and polishes in one application
• No need for water!
• Long lasts lustre
• No residual dust or streaks
• Non-sticky
• Powder free
• Suitable to use on bicycles, motorcycles, cars & R.V's
• Safe to use on Carbon Fibre

HOW TO

1. Shake the bottle vigorously to activate formula.
2. Spray onto the surface and leave for a time to penetrate the light contaminants.
3. Now gently wipe the area with a clean, dry microfiber cloth. With each wipe fold the cloth to a clean side.
4. Using another clean microfiber cloth buff all areas to leave a showroom shine.
5. Do not use on heavy grit/grime or stubborn contaminants as this will inevitably lead to surface scratching.
6. Always use microfiber cloths as they trap the dirt away from the surface.

The Muc-Off Motorcycle Care Kit is the essential one-stop kit for moto care and maintenance, containing all the basic elements you need to keep your motorbike looking box-fresh for longer!

FEATURES

Motorcycle Cleaner

• Safe on all parts and surfaces including carbon fibre
• Will not harm seals, cables, brake pads or rotors
• Safe on anodized metal
• Alkaline based and free from CFCs, solvents or acids
• Nano Tech Formula cleans on a molecular level
• Biodegradable
• How to:
  • Step 1 - Rinse motorbike thoroughly before applying Nano Tech Motorcycle Cleaner.
  • Step 2 - Spray Nano Tech Bike Cleaner onto the entire motorbike including components and leave for 3-5 minutes. Do not let it dry or apply in direct sunlight.
  • Step 3 - Agitate any stubborn grime with a brush or sponge.
  • Step 4 - Rinse entire bike thoroughly with fresh, clean water.

Motorcycle Protectant

• High-performance formula leaves dry, non-sticky protective film
• For use after washing to drive out excess water
• Prevent dirt adhesion
• Makes an ideal winter protectant
• Quick and easy to use

Microcell Sponge

• Bike friendly size
• Expands after opening
• Ergonomic design