Cleaning & Maintenance

New! OptiMate 1 Duo features precise microprocessor controlled charging and long term maintenance. Maintain any type of 12 volt lead-acid battery, filler cap / wet cell, sealed AGM (MF) or GEL and 12.8/13.2V lithium (LiFePO4) batteries without overcharging. Ideal for vehicles that are seldom or seasonally used, or in storage. The OptiMate maintenance program delivers only what the battery needs, never overcharges, never undercharges.

• Ideal for Standard, AGM & gel 12V batteries from 2 – 30Ah & Lithium (LiFePO4) 12.8/13.2V batteries
• Cost-effective 12V battery maintenance
• 0.6A (constant current) charging amps
• Indoor use (lowest temperature: -4°F / -20°C)
• Low Volt Start of 4V
• Global input (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
• Dust proof plug-in case, with 12ft / 370cm charge lead ending in SAE connector
• No risk of overcharging, totally safe for vehicle electronics
• Sparks suppressed, Safe for long-term battery maintenance, Automatic shut-down if short-circuited or battery disconnected
• Weatherproof battery lead & battery clip set included

Smart in-line 3300mA USB charger kit, with standby mode and vehicle battery monitor.

The sealed in-line battery to USB 3300mA charger with 200cm / 80″ of cable and O-31 battery lead, delivers safe and fast USB charging of any device mounted outside on the handlebar or inside your tank or pannier – Cable routes to where USB charging is needed!

Supply cable (100cm / 40″) with M6 / 1/4″ rings fit all powersport battery terminals. – Fuse protected.

Charges 1x USB device with up to 3300mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Weatherproof USB charge port easily zip-tie to handlebar, strut or even brake / clutch cable – Seals againt inserted USB cable for charging in any weather!

Built in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – Indicates battery is ‘start ready’ at the blink of an LED!

Smart 2400mA USB charger, with standby mode & vehicle battery monitor.

The portable & compact SAE to USB 2400mA charger for safe and fast charging of any USB device, including your phone, camera or GPS.

Connects to battery lead with industry standard SAE 2-pin connector – Seals perfectly when mated with OptiMate SAE!

Charges 1x USB device with up to 2400mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Creates weatherproof seal against inserted USB cable, or ‘rideproof’ cap seals when not in use – Worry free phone, camera or GPS charging in any weather!

Built-in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – indicates battery is ‘start ready’ at the blink of an LED!

Technosynthese® 4-Stroke lubricant – Ester technology - Improved shear resistance. Smooth shifting. Meets JASO MA2 specifications for optimal wet clutch performance. Suitable for catalytic converters.

Types of Use

Street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 Stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe... Suitable for specific SUZUKI, YAMAHA, KAWASAKI engines requiring SAE 10W-40 viscosity grade oil. Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

Protection

Synthetic lubricant Technosynthese® reinforced by Ester base stock to warranty anti-wear properties and improve gear protection and lifetime. Improved oil film resistance at high temperatures for engine durability. Optimized Phosphorus and Sulfur content (JASO MA2 < 1200 ppm) for better operating conditions of catalytic converters. The innovative anti wear additives package provides excellent gearbox protection. FZG Gear Test results: Pass FLS 14. The FZG (Forschungsstelle für Zahnrader und Getriebebau) Test, evaluates fluid lubricating and wear protection properties at the interface of a loaded set of gears.

Comfort

JASO has created its own 4-stroke motorcycle standard -JASO T903- which has three grades MA, MA1 and MA2. JASO MA2 offers the most efficient friction levels to guarantee the clutch engagement during the three riding modes: Starting, Acceleration and Constant Speed.

100% Synthetic Ester based motorcycle lubricant for high performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial fitted with 4-stroke engines, integrated or non-integrated gearbox, wet or dry clutch, engines meeting Euro 2 or Euro 3 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe. 

Types of Use

High performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems : catalytic converters, air injection into exhaust pipe...

Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

HD 80W-90 is an Extreme Pressure gearbox and differental lubricant.

Motul HD 80W90 Transmission Oil

Motul's most robust gearbox oil is the HD 80W90 Transmission Oil. Prepared for abuse, Motul HD Transmission Oil is suitable for all mechanical transmissions: synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes and hypoid differentials without limited slip systems. Motul HD is anti-foam, anti-corrosion and stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard.

Features: 

• Fully conventional formulation
• Designed especially for high load applications
• Extreme anti-wear properties
• Stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard
• Suitable for all transmissions without limited slip systems
• Safe for synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes or hypoid differentials
• Recommended for heavy loads and low revolution speed or moderate loads and high revolution speed
• See spec sheet for full details
• Meets or exceeds API GL-4, API GL-5

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF204RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models, including most Triumphs. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/hf204rc

If you’re changing your oil filter, make sure to also pick up a new oil drain plug washer here.

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF153RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/HF153RC

FEATURES

• Long Life 100% synthetic fluid
• Applications: All types of hydraulic actuated-brake and clutch systems in accordance with DOT 5.1, DOT 4 and DOT 3 manufacturers' recommendations.
• Fluidity specially designed for anti-locking brake system (ABS)

SPECIFICATIONS

• Dry Boiling Point: 270°C (518°F)
• Wet Boiling Point: 185°C (365°F)
• Standards: FMVSS 116 DOT 5.1 non silicone base & DOT 4 & DOT 3 / SAE J 1703

Colorless and sticky lubricant specifically designed to lubricate all chains of road bikes and karts.

Types of Use

All types of chains: standard and with O-RING, X-RING, Z-RING. Street motorcycles, go-karts. Specially recommended for very fast motorcycles, MOTUL CHAIN LUBE ROAD adheres to the chain even at high speeds.

Package size: 400ML (9.3OZ)

Colorless and sticky lubricant specifically designed to lubricate all Off-road chains.

Types of Use

All types of chains : standard and with O-RING, X-RING, Z-RING.
Cross, enduro, trial, trail motorcycles or quads, ATVs.
Specially recommended for off road use: MOTUL CHAIN LUBE OFF ROAD repels sand and soil.

Package size: 400ML (9.3OZ)

• Double-ended brush for cleaning chains and other components
• Three-sided brush to clean chain rollers and side plates in one operation
• Long, straight bristles on opposite end to clean hard to reach areas
• Durable nylon brush and high quality plastic handle

IPONE VISOR RAIN OFF is a visor cleaner with a water-repellent effect. It places a protective film on the visor allowing water to slide off easily.

Spray the product on the visor, let it dry for 2 minutes and wipe with a soft cloth.

• Repels water from helmet visor
• Improves visibility by shedding water
• Suitable for glossy and matte helmets
• No marks

Cleaning and nourishing cream formulated with olive oil soap, glycerine and turpentine oil. Cleanses, nourishes and revives all types of leather on motorcycles or motorcycle gear from jackets, to boots, and gloves.

Like water off a duck's back. This product extends the life of your leather and wax items. The ultimate in long lasting protection. Won't stain stitching. Sweet smelling and insect repelling. Leather Food. Moisturise-soften-preserve. Helps to waterproof your leather. Reduces water absorption. Conditions and revives the look of the leather or wax fabric. Works on wax cotton (Barbour type) jackets too! 

Suitable for use of motorcycle clothing, equestrian equipent and footwear. 

Product info:

• 1 x 150 mL tin of Goldtop Ducks Wax Water Repellent Balm
• Effects on tan coloured gloves as shown here on Youtube

Like water off a duck's back. This product extends the life of your leather and wax items. The ultimate in long lasting protection. Won't stain stitching. Sweet smelling and insect repelling. Leather Food. Moisturise-soften-preserve. Helps to waterproof your leather. Reduces water absorption. Conditions and revives the look of the leather or wax fabric. Works on wax cotton (Barbour type) jackets too! 

Suitable for use of motorcycle clothing, equestrian equipent and footwear. 

Product info:

• 1 x 30 mL tin of Goldtop Ducks Wax Water Repellent Balm
• Effects on tan coloured gloves as shown here on Youtube

NOTE: Due to manufacturer restrictions, this item cannot be shipped to addresses outside of Canada.

The maintenance of textile garments requires special attention, especially when they contain waterproof and breathable membranes. REVIT! TEXTILE WASH detergent maintains the specific qualities of breathable waterproof clothing, when washing by machine or hand.

Always follow the wash and care instructions on garment labels.

NOTE: A $75 handling fee is applied to shipping cost due to this item being oversize/overweight.

Our Hybrid Headlift Stand will lift your motorcycle from the hole in the lower triple tree(steering stem), allowing you to remove the tire, remove/service the forks, or just store the bike with no load on the suspension.   The Hybrid Headlift Front features 7 indexable height adjustments, which is very desirable when removing the forks on your motorcycle. 

You will have several options below when adding this item to your cart.  The most important option is the front pin.  You'll need to review our pin fitting chart or information in our bike-specific categories to determine which pin is right for your motorcycle and year model. 

There are welded-on "bungs" on the upper part of this stand that you can attach our caliper holders to if you'd like to have a place to mount your calipers and caliper bolts while working on the front of the bike. 

You'll also be asked to decide whether you want an axle holder.  The Axle Holder is exactly what it sounds like: something to hold your axle when you remove it from the motorcycle.  It is not necessary, but a nice option if you like that concept.

The Wall Mount is another item that is exactly what it sounds like:  something you can use to hang your stand up on the wall of your shop or trailer.  The "Shop Kit" comes with the Front Stand Retainer only, which is great for a shop/garage.  The "Transport Kit" comes with an adjustable bungee cord and d-rings to mount your stand on the wall of the trailer.  

The Hybrid Headlift is based upon a modular design and can be easily converted to lift from the forks instead of the lower triple tree with the addition of hybrid swivels (related products below). 

The Hybrid Headlift Front Stand comes standard with a 16" removable handle you can choose  for maximum leverage and of course the convenience of not having the handle be a trip hazard when the bike is left on the stand.  Pit Bull stands are known for our distinctive gold and red finish and are not available in other colors.

NOTE: A $75 handling fee is applied to shipping cost due to this item being oversize/overweight.

The Spooled Forward Handle Rear lifts spool-equipped bikes. It is width adjustable to fit virtually all sport bikes. It is also height adjustable to set clearance under rear wheel. Same as Standard Forward Handle Rear except for interchangeable top supports. Sold complete with top supports.

Advantages to the forward handle stands: a)user can hold bike's handgrip when getting stand into place, b)no part of stand is behind bike, and c) lower bar of stand helps align axle when installing rear wheel.

NOTE: Not recommended for Moto Guzzi, Buell XB Series, Vintage or 125GP machines.

NOTE ABOUT REMOVABLE HANDLE:  As of Winter 2022, this stand only comes with a removable handle. This is primarily beneficial for storage and/or shipping.  This handle is not removable while the stand is in use but has become a favorite among customers who need this stand to store flat when not in use.  This is also a very handy option for international shipping as it will be able to go in a flat box.

FITTING NOTES

Width Adjustability: 9-7/8" - 15-1/2"

Height from Ground: 12-3/4" - 15-1/2"

For instructions for use, click here.

NOTE: A $75 handling fee is applied to shipping cost due to this item being oversize/overweight.

Pit Bull’s new Pit Crew Tire Wedge is a height-adjustable device that allows one person to easily align and steady motorcycle wheels so axles are easy to remove and install.

The Tire Wedge can be used with most Pit Bull front and rear stands made in the last 20 YEARS. It quickly attaches without hardware using a solid press fit. Once in place below a tire, height can be set between 0.75 to 4.9 inches with a twist of its adjustment knob. This positioning allows wheel spacers and brake-caliper mounts to be perfectly lined up so axles slide in and out without binding.

The first of five innovative new products introduced by Pit Bull in 2015, the Pit Crew Tire Wedge makes changing tires easier than ever. Made from steel and zinc-plated to fend off the elements, like the company’s legendary stands, it's built to outlast any motorcycle and comes with a lifetime warranty. Designed and manufactured in the USA.

Defining Features
Allows axles to quickly slide in and out without binding
Quickly aligns axle spacers and brake-caliper mounts
Adjustable height: 0.75 to 4.9 inches
For use with Pit Bull stands manufactured in the last 20 YEARS
Quick-release design attaches without hardware
Zinc plated to resist the elements
Made in the USA
Lifetime warranty

NOTE: Will not work on Forward Handle Rear Stands or Single Sided Swingarm Stands. Will also not work with our original Standard Front Stand or when using the Forklift Converter (F0015-002).

NOTE: Stand in photo is for demonstrating how the product works. Stand not included when you purchase the Pit Crew Tire Wedge.

S1000RR, S1000R, HP4, 899/959 Panigale, Monster 821, & Triumph 675 Owners: You will need two 929 Shims on your rear stand to use the Tire Wedge. Some taller aftermarket tires may not require the shims.

Counteract CBB-EP8 Tire/Tube Mounting Compound 8lb Bucket

• Designed to assist in mounting rubber tires and tubes on all types and sizes of wheels
• Fortified with rust inhibitors to provide protection against corrosion of aluminum or alloy wheels
• Fully compatible with Counteract balancing beads
• Fast-drying formula will not freeze
• Performs well on low profile tires or tires with stiff beads
• Environmentally friendly and petroleum-free
• Reduces wear and tear on tire changing equipment
• Available in 8lb bucket

• Easily apply your tire mounting lubricant with control.
• Perfect for euro paste mounting formulas.
• Works best with Counteract Euro Paste tire and tube mounting compound.
• Premium quality brush with soft and flexible head.
• Angled head allows for easier application.

• Flexible shaft allows easy access to awkward locations during removal and installation of hose clamps
• Comfortable grip, high-torque handle
• Hollow drive handle stores sockets and bits
• Contains: 4, 6, & 8mm sockets, 4mm flat head bit and Phillips #2 bit
• Length: 300mm

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• Size: 51-120mm (2" - 4 3/4") dia.
• Overall length: 285 mm (11-1/4")

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• 32 - 76 mm: Overall length: 215 mm (8-7/16")

Fuel Friend Canister, 2Ltr Black

These great little cans made by Hünersdorff in Germany are exactly what you need for a small, yet solid and safe fuel reserve. Specifically made for storage and transport of hazardous substances, perfect for motorcycle trips, all small engines and many other purposes.

Details:

• The smallest can suitable for fuel nozzles on the market
• Emergency reserve for motorcycles, scooters, quads and other small engines
• Small, extremely robust, meets the highest safety requirements
• Suitable for all fuels and petrol products.
• Made in Germany
• Extremely stable
• Filling opening suitable for fuel nozzles
• Patented design
• Weight: 0.44 kg
• Dimensions: Width x Depth x Height - 14 × 9 × 25 cm
• Does fit in the Kriega OS-Bottle Holder, sold separately

The following accessories can be purchased separately if desired:

• Flexible spout
• Lockable rigid spout

SKU: FFB20black

GTIN: 4007228815719

Fuel Friend Canister, 1.5 ltr Red

These great little cans made by Hünersdorff in Germany are exactly what you need for a small, yet solid and safe fuel reserve. Specifically made for the storage and transport of hazardous substances, perfect for motorcycle trips, all small engines, and many other purposes.

Details:

• The smallest can suitable for fuel nozzles on the market
• Emergency reserve for motorcycles, scooters, quads, and other small engines
• Small, extremely robust, meets the highest safety requirements
• With eyelets fitted to the sides for securing with a tension strap (max 25mm width) or similar.
• Suitable for all fuels and petrol products.
• Made in Germany
• Extremely stable
• Filling opening suitable for fuel nozzles
• Patented design
• Weight: 0.32 kg
• Dimensions: Width x Depth x Height: 12.5 × 6.5 × 27.5 cm
• Does fit in the Kriega OS-Bottle Holder, sold separately

The following accessories can be purchased separately if desired:

• Flexible spout
• Lockable rigid spout

SKU: FFP15red

GTIN: 4007228815511

Foldable funnel for clean filling of the FuelFriend® 0.5 litre canisters. These are also helpful for a clean pour of fuel into the fuel tank of your motorcycle. A

lso suitable for clean filling of gear oil, engine oil, coolant, etc.

Details:

• Small, foldable funnel is easy to transport
• Suitable for all fuels and petrol products
• Made in Germany
• Outer diameter of the funnel exit: 1.5 cm
• Weight: 0.02 kg
• Dimensions: 6.5 × 6.5 × 2.5 cm

Spout with bellows, black, HD-PE, for fuel cans

• suitable for all current tank openings (petrol and diesel) and all vehicles with petrol misfuelling inhibitors (not suitable for vehicles with diesel misfuelling inhibitors)
• Accessories for FuelFriend 1L, 1.5L and 2L Canisters - sold separately
• With bellows
• Enables easy emptying of jerrycans
• Nozzle external diameter = approx. 20mm
• Length = 265 mm
• outside thread diameter = 38 mm / inside diameter of filling opening = 29 mm
• Made by Hunersdorff in Germany

SKU: 819702

GTIN:

4007228819724

Rigid petrol spout with closure, black, HD-PE for fuel canisters

• rigid spout with screw cap closure and carrying loop for fixing on the can
• with union nut for exact positioning with small tank openings
• captive screw cap
• for combined jerrycan ECO + PROFI
• suitable for FuelFriend 1L, 1.5L, and 2L canisters - sold separately 
• Length = 130 mm
• Nozzle external diameter = 21 mm
• for a = outside thread diameter = 38 mm / (for w = inside diameter of filling opening = 29 mm)

SKU: 

819901

GTIN: 

4007228819908

This 0.5-litre can is ideal for carrying extra fuel, engine oil, 2-stroke oil, brake fluid, or other liquids on your trips. 

More and more people are using lighter Enduro motorcycles for long adventure trips. The downside is that you may have to add some engine oil during the trip, yet you want to avoid carrying a sizeable 1-litre oil container. That's why these small 0.5 litre cans are ideal. They don't take much space, are very strong, and the screw cap opening is small enough to pour oil into your engine without a funnel.

• Small, extremely robust, meets the highest safety requirements
• Suitable for ethanol fuel E10, oil, and brake fluids
• Small enough, no funnel is needed
• Captive screw cap

Note: It can be used for fuel, but a pump nozzle will not fit.

Details:

• Small pack size
• Spout sold separately
• Suitable for all fuels and petrol products.
• Made in Germany
• Extremely stable
  
• Patented design
• Weight: 0.12 kg
• Dimensions: Width x Depth x Height: 9.5 × 5.5 × 16 cm

The following accessories can be purchased separately if desired:

• Rigid spout for pouring
• Foldable funnel

SKU: FF05clear

GTIN: 0797337278720

Spout red, HD-PE

• for FuelFriend 0.5 L canisters - sold separately 
• with rubber rings 6/32 black
• outside thread diameter = 24 mm / inside diameter of filling opening = 18 mm
• Made by Hunersdorff in Germany

SKU: ET-281302

GTIN:

4007228281293

MOTUL Fuel System Clean 300ml
MOTUL FUEL SYSTEM CLEAN is designed to be used in all types of gasoline engine with injection or carburettors, naturally aspirated or turbocharged with or without catalytic converter, using all kind of gasoline. MOTUL FUEL SYSTEM CLEAN effectively cleans dirtying and clogging which appear in the whole fuel system: 
- condensation in the fuel system 
- gumming in the carburettor 
- injector nozzle fouling 
- dirtying of combustion chambers and inlet valves 

MOTUL FUEL SYSTEM CLEAN provides a perfect lubrication during cleaning process and prevents removed micro-particles from depositing. 

A clean fuel system is a necessary condition for an effective engine running. MOTUL FUEL SYSTEM CLEAN allows to: 
- clean the carburettors or the injectors (for a better atomisation) 
- prevent the formation of deposits and varnishes on inlet valves and in combustion chambers 
- disperse condensation water in order to avoid any fuel system oxidation 

A regular use will provide: 
- optimum engine performances 
- fuel savings 
- increased lifetime of fuel system and catalytic converter 
- a reduction of exhaust pollutants emissions 

Directly pour one can of FUEL SYSTEM CLEAN in the tank before refuelling, regularly, depending on the use (shorten intervals in urban use). The fuel system will be then completely cleaned, from the tank to the combustion chamber. A can of FUEL SYTEM CLEAN is sufficient for tank capacity up to 60 litres. 
In case of bigger tank capacity, the recommended mixing ratio is 0.50% (200:1). Do not exceed the recommended proportion. If necessary, proceed to 2 successive treatments. 
Curative treatment : use the product pure by plugging on the fuel system with the adaptation kit

• Concentrated octane booster increases pump gas octane rating
• Eliminates pre-detonation
• Mix either with straight gas or with alcohol and nitrous mixtures
• For 2- or 4-stroke engines
• Legal for all racing applications
• Won't harm or discolor plastic gas tanks
• Cleans fuel delivery systems
• Each ounce (EU: 29.57 ml) of octane booster per gallon (EU: 3.79 L) of gas raises octane rating by four points
• Made in the U.S.A.